SongVault Artist Profile


No Tracks Available
sk789ww sk789ww
sk789ww sk789ww

Maine, Germany

Cajun / Zydeco / Delta Blues

Listen to sk789ww sk789ww
How to Ensure a High Quality PLC Splitter?

PLC (Planar Lightwave Circuit) splitter is an important component in PON (passive optical network) where a single optical input is split into multiple outputs. This makes it possible to deploy a Point to Multi Point physical fiber network with a single OLT (optical line terminal) port serving multiple ONTs (optical network terminal). The most common split ratios are 1:N or 2:N. N represents the output ports, usually as 2, 4, 8, 16, etc. The optical input power is distributed uniformly across all output ports. The PLC Splitter shares the cost and bandwidth of the OLT and reduces fiber lines. This article will tell about how to keep a high quality PLC splitter from manufacturing to testing sides.

PLC splitter is composed by many miniature parts. Among them, there are three main components: fiber array for the input and output, and the chip. These three main components decide whether the PLC splitter is of good quality or not. Let’s see the key manufacturing steps of a PLC splitter.

Then how to determine the quality of a Mini PLC Splitter? The GR-1209 standards provides comprehensive optical performance criteria. The following will introduce these specifications such as optical bandpass, insertion loss, return loss, uniformity and directivity.

In a PON system, the downstream transmission uses 1490nm wavelength and 1310nm wavelength for the upstream transmission. Besides, the requirement for RF video overlay and network testing/maintenance should also be considered. The transmission wavelength for RF video is 1550 nm. And the wavelengths for networking testing and maintenance are 1550 nm and 1625 nm. So the standard opterating wavelength for a PON splitter is determined as 1260~1650 nm which covers most of the optical bands.

Uniformity means the maximum insertion loss value between one input port and any two output ports or between two input ports and one output port. This can ensure that the transmission power at each ABS PLC Splitter output port is the same in a PON system to simplify the network design.

Directivity is the part of power transferred from one input port to another input port or from an output port to another output port. For a 2xN optical splitter, when light injects into one of the input ports, light doesn’t only propagate out of the output ports. Some of the light propagates back through the second input port. And when the light injects into one of the output ports, light propagates back through the other output ports. In a bidirectional transmission system such as a PON, directivity is useful to reduce signal crosstalk. A high directivity value will increase the insertion loss due to the optical power loss.

In FTTx and PON architectures, fiber optic splitter is an important component to share the optic network with multiple users. The basic principle of fiber optic splitter is to split one optic light beam into several parts at a certain ratio. According to different manufacture technologies, fiber optic splitters can be divided into PLC splitter and FBT Splitter. You may wonder the differences of the two splitter types when making a choice between them. This article aims at helping you to understand their distinctions and make better decisions.

FBT, or fused biconic taper uses the traditional technology to fuse several fibers together closely. Fibers are aligned by heating for a specific location and length. Fusion process will not stop until the parameters of the fibers reach the required standards. Since fused fibers are very fragile, they are protected by a glass tube made of epoxy and silica powder. Then a stainless steel tube covers the inner glass tube and is sealed by silicon. ABS FBT Splitter is also widely used for different applications.

Since their invention in the 1970s, Fiber Optic Assemblies have greatly changed the way wires and wire-dependent industries work. In the communications industry alone, fiber optic cable types have largely replaced copper wire as the primary means of signal transmission. Their use, however, spans a wide array of applications, including cable television, educational institutions, electrical utility plants, industrial companies, medical technologies, and military operations.

Fiber optic cable assemblies consist of an optical fiber, a reinforcement strand for support, and fiber optic cable connectors. While copper wires depend on electrical pulses to transmit data, fiber optic systems rely on light pulse transmissions carried through the cable which delivers data at a quicker rate.

The Optical Distribution Cabinet can also be called the optical fiber distribution cabinet. It is an upgraded version of the odf optical fiber distribution cabinet. It is also used for fiber termination, fiber fusion splicing, fiber wiring and fiber storage, but it uses the tray in the box to slide down. Out-of-line design, so that you can install both the adapter panel and the high-density MPO/MTP wiring box. It is a commonly used wiring tool for local area networks and data centers, and can ensure long-term and reliable network transmission.

The optical fiber distribution cabinet has various specifications, the common ones are rack type and wall-mounted box type. U or RU as the unit, refers to the height of the equipment designed to be installed in the rack, usually 1RU, 2RU, 4RU size. It has a sliding-out and sliding drawer design, which not only can be flexibly wired but also can protect the optical fiber very well. It is an ideal wiring management solution for data centers.

Fiber optic adapters (also known as Fiber couplers, Fiber Adapter ) are designed to connect two optical cables together. They have a single fiber connector (simplex), dual fiber connector (duplex) or sometimes four fiber connector (quad) versions. The Fiber Optical Adapter can be inserted into different types of optical connectors at both ends of the optical fiber adapter to realize the conversion between different interfaces such as FC, SC, ST, LC, MTRJ, MPO and E2000, and is widely used in optical fiber distribution frames (ODFs) Instruments, providing superior, stable and reliable performance.

The optical fibers are connected by an adapter through its internal open bushing to ensure the maximum connection between the optical connectors. In order to be fixed in a variety of panels, the industry also designed a variety of finely fixed flange.

Transformable optical adapters are available with fiber optic connectors of different interface types on both ends and provide a connection between APC faceplates. Duplex or multi-adapter adapts to increase installation density and save space.

Browse by:   A B C D E F G H I J K L M N O P Q R S T U V W X Y Z  

Search for a song or artist:

SongVault Account Artists, upload up to 18 Songs on your profile!


©COPYRIGHT 2023 SongVault, LLC